TURBOJET

The turbojet is the engine in most common use today in high-speed, high-altitude aircraft, not in Army aircraft. With this engine, air is drawn in by a compressor which raises internal pressures many times over atmospheric pressure. The compressed air then passes into a combustion chamber where it is mixed with fuel to be ignited and burned. Burning the fuel-air mixture expands the gas, which is accelerated out the rear as a high-velocity jet-stream. In the turbine section of the engine, the hot expanded gas rotates a turbine wheel which furnishes power to keep the compressor going. The gas turbine engine operates on the principle of intake, compression, power, and exhaust, but unlike the reciprocating engine, these events are continuous. Approximately two-thirds of the total energy developed within the combustion chamber is absorbed by the turbine wheel to sustain operation of the compressor. The remaining energy is discharged from the rear of the engine as a high velocity jet, the reaction to which is thrust or forward movement of the engine. The turbojet is shown schematically in figure 1.3.

Figure 1.3. Axial-Flow Turbojet Engine.

BRAYTON CYCLE OF OPERATION

Ambient air is drawn into the inlet section by the rotating compressor. The compressor forces this incoming air rearward and delivers it to the combustion chamber at a higher pressure than the air had at the inlet. The compressed air is then mixed with fuel that is sprayed into the combustion chamber by the fuel nozzles. The fuel and air mixture is then ignited by electrical igniter plugs similar to spark plugs. This ignition system is only in operation during the starting sequence, and once started, combustion is continuous and self-sustaining as long as the engine is supplied with the proper air-fuel ratio. Only about 25 percent of the air is used for combustion. The remaining air is used for internal cooling and pressurizing.
The turbine engines in the Army inventory are of the free-power turbine design, as shown in figure 1.2. In this engine, nearly two-thirds of the energy produced by combustion is extracted by the gas producer turbine to drive the compressor rotor. The power turbine extracts the remaining energy and converts it to shaft horsepower (shp), which is used to drive the output shaft of the engine. The gas then exits the engine through the exhaust section to the atmosphere. Army helicopters use a divergent duct to eliminate the remaining thrust. The various kinds of exhaust ducting are discussed in detail with the engine using that particular ducting.

Figure 1.2. Typical Free-Power Turboshaft Engine

Thermal expansion valve

Thermal expansion valve(ATA 21)

A thermal expansion valve  is a component in refrigeration and air conditioning systems that controls the amount of refrigerant flow into the evaporator thereby controlling the superheat at the outlet of the evaporator. This is accomplished by use of a temperature sensing bulb filled with a similar gas as in the system that causes the valve to open against the spring pressure in the valve body as the temperature on the bulb increases. As temperatures in the evaporator decrease, so does the pressure in the bulb and therefore on the spring causing the valve to close. An air conditioning system with a TX valve is often more efficient than other designs that do not use one.

Self-sealing fuel tank

In aviation, self-sealing fuel tank is a fuel tank technology in wide use since World War II that prevents fuel tanks primarily on aircraft from leaking fuel and igniting after being damaged by enemy fire.

Self-sealing tanks have two layers of rubber, one of vulcanized rubber and one of untreated rubber that can absorb oil and expand when wet. When a fuel tank is punctured, the fuel will spill on to the layers, causing the swelling of the untreated layer, thus sealing the puncture.

Most jet fighters and all US military rotary wing aircraft have some type of self-sealing tanks. Military rotary wing fuel tanks have the additional feature of being crashworthy. High altitudes require the tanks to be pressurized, making self-sealing difficult. Newer technologies have brought advances like inert foam-filled tanks to prevent detonation. This foam is an open cell foam that effectively divides the gas space above the remaining fuel into thousands of small spaces; none of which contain sufficient vapour to support combustion. This foam also serves to reduce fuel slosh. Major manufacturers of this technology include Amfuel (Zodiac) (formerly Firestone), Engineered Fabrics Corp. (Meggitt) (formerly Goodyear), GKN USA and FPT Industries. For military use, tanks are qualified to MIL-DTL-27422 and MIL-DTL-5578.

In additions to fighter aircraft some military patrol vehicles and armoured limousines for VIP use also feature self-sealing fuel tanks.

Wingtip device

Wingtip devices are usually intended to improve the efficiency of fixed-wing aircraft. There are several types of wingtip devices, and though they function in different manners, the intended effect is always to reduce the aircraft's drag by altering the airflow near the wingtips. Wingtip devices can also improve aircraft handling characteristics and enhance safety for following aircraft. Such devices increase the effective aspect ratio of a wing without materially increasing the wingspan. An extension of span would lower lift-induced drag, but would increase parasitic drag and would require boosting the strength and weight of the wing. At some point, there is no net benefit from further increased span. There may also be operational considerations that limit the allowable wingspan (e.g., available width at airport gates).

Wingtip devices increase the lift generated at the wingtip (by smoothing the airflow across the upper wing near the tip) and reduce the lift-induced drag caused by wingtip vortices, improving lift-to-drag ratio. This increases fuel efficiency in powered aircraft and increases cross-country speed in gliders, in both cases increasing range.

Winglets are employed on many aircraft types, such as:

• Rutan VariEze, the first aircraft to use winglets (1975)
• Learjet 28/29, the first production jet aircraft to use winglets (1977)
• Glaser-Dirks DG-303, an early glider derivative design, incorporating winglets as factory standard equipment
• Airbus A310-300, the first airliner to feature wingtip fences (1985)
• Boeing 747-400, the first mainline airliner to feature winglets (1988)
• Ilyushin Il-96, first Russian and modern jet to feature winglets (1988)
• Tupolev Tu-204, first narrow body aircraft to feature winglets (1994)

Lightning detection

A lightning detector is a device that detects lightning produced by thunderstorms. There are three primary types of detectors: ground-based systems using multiple antennas, mobile systems using a direction and a sense antenna in the same location (often aboard an aircraft), and space-based systems.


For more http://avionics0.blogspot.com/2010/12/lightning-detection.html

Compare Airbus 320 family